Söfnunar árátta getur veri skemmtileg

---

Barrel Length - 25.65 inches: 4-groove, RH, concentric rifling, 1 in 10.63
Overall Length - 43.6 inches
Weight - 8.85lbs empty
Action - Straight Pull  Bolt Action
Caliber - 7.5x55 Swiss (GP11)
Capacity - 6 round detachable box magazine
Sights - Tangent-leaf sight graduated to 1500m
Total Production - 528,230
Bayonet: Models 1899/18, 1918, 1918/55 and 1914 Pioneer (Sawback)

By the end of the 1920s the Swiss began to question whether or not they should equip their soldiers with rifles or carbines.  Indeed, 2/5^th of the Infantry and 3/5^th of the rest of the army were already equipped with carbines rather than long rifles.  While the rifles provide better accuracy and range, the carbines were lighter and easier to handle.   Interestingly enough, while the carbines accuracy was considered adequate for military purposes, it was the member of the various private Swiss shooting clubs that were insisting the more accurate rifle be kept in service.

  In 1928, first attempt at combining the positive qualities of the rifle and carbine was made by fitting a K11 with a heavy barrel.  200 heavy barreled carbines were produced and tested.  However, the gains in accuracy were outweighed by the added cost of the weapon.  The decision was made in April 1929 that a new design for the carbine. 

The following requirements were set for the new weapon

1. The new weapon should not be significantly longer than the 1911 Carbine.
2. The new weapon should have a straight-pull action
3. The new weapon should be more accurate than the 1911 Carbine, and as accurate as the 1911 Rifle
4. The new weapon should be cheaper to produce than the 1911 series.

 Testing began in late 1929 and continued into 1930 of two prototype designs, and end with favorable results.  In late 1930 10 new design carbines were sent to the shooting school in Wallenstadt for evaluation.  The new design carbine’s accuracy was compared with that of the 1911 Rifle and the heavy barreled carbine.    The results of the testing showed the new design carbine to be more accurate than either the rifle or the heavy barrel carbine.   However, there were some design issues that needed addressing.

In May 1931, a series of 200 improved carbines were produced.  These carbines were issued to various shooting schools as well as six recruit schools.   The testing continued until October 12, and produced the following conclusions:

 

1. The new bolt design was less prone to binding.
2. There were fewer feed problem.  
3. The new action was less prone to failure, even in the event of one of the locking lugs breaking.
4. The new stronger action was better able to survive firing with a barrel blockage.
5. The new designs proved very durable, four carbines had 150,000 rounds fired through them without any appreciable failures.

Unlike the previous Schmidt-Rubin series of rifles, the new carbine’s locking lug locked up immediately behind the chamber.  This afforded several advantages.  The entire action was strengthened as the lugs were locking in a much thicker part of the action.  Lock-up was also more precise.  The bolt was significantly shortened, allowing for a longer barrel and sight radius, without increasing the overall length of the rifle, moving the rear sight closer to the eye, and cutting in half the amount of time for the firing pin to strike the cartridge after the trigger was pulled. 

The new carbine also had several other new features.  The barrel was intended to be free floating.  The action itself only connected to the stock by two screws, one attaching to the chamber, with the second attaching to the tang.  This allowed the Swiss to eliminate the aluminum barrel collar used in the Schmidt-Rubin series.  The trigger was redesigned, as were the magazine and rear sight. 

The end result of these modifications produced a rifle that was more accurate, yet cheaper than the K11, it was replacing.  In 1932 it was estimated that the cost of a K11 would be 169 Swiss Francs.  Conversely, the new carbine had an estimated cost of 151 Swiss Francs. 

On March 17, 1932, the Swiss Upper Parliament accepted the new carbine into service and designated it the Model 1931. 

During it’s production run there were several minor modifications made to the K31. 

1934, the firing pin was made thinner.
1935, the receiver was hardened
1936, the magazine shell was hardened
1941, laminated stocks were tested, but rejected
1944, due to supply shortages, Chromium Molybdenum was use in place of Chromium Nickel Steel on various parts.  This experiment proved unsuccessful.
1946, starting with serial number 868,901, beech rather than walnut was used for making the stocks.

The K31 stayed in front line service until 1958, when it was replaced by the Stgw57.  K31s were still found with some Swiss Military units, well into the 1970s.  The total production run was 528,230 carbines, beginning in 1933 and ceasing in 1958.

Mig vantar einn svona í safnið

Model 1918 Bayonet

Blade Length - 11.81" (300mm)
Handle Length - 5" (124mm)
Total Length - 17" (431m)
Muzzle Ring Diameter - .56" (14mm)
Issued with : Schmidt-Rubin Models 1911 Carbine, K31
Manufacturer: Waffenfabrik Neuhausen, Elsener Schwyz (AKA Victorinox)

Description:  The Model 1918 has a double-edged blade and lacks a fuller.  A variant exists in the form of the Model 1918/55.  The 1918/55 has a 1918 blade fitted on a  handle which is similar (but not identical) to the one used on the Model 1914..

The Schmidt-Rubin Series  
Fyrir áhugamenn um Schmidt-Rubin